NETGEAR - Firmware

Firmware 5.0.0.15 pour GS724TP

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:53:45 +0200

Firmware 5.0.0.15 pour GS724TP

Bug Fixes :

Fixed the problem that device does not handle MSTP packets when its Spanning Tree configuration is set to RSTP.
Fixed the problem that GS748TP combo ports (port 45, 46, 47, and 48) may disconnect every few minutes and system log would show media type toggles between copper and fiber repeatedly.
Fixed the problem that the switch may reboot and the following log message would be generated: "FATAL ERROR: SW2M: ABORT DATA exception".

Limitations and Known Issues :

Although Management VLAN can now be changed from VLAN 1 to any other valid VLAN, egress packets still cannot be tagged with VLAN ID of 1.
When configuring IP ACL rule, system does not reject source address to be multicast address and accepts 0.0.0.0 masking.
When specify IPv6 ACL rule, the permit all (permit any any) rule would only forward the packet with IP header. As a result, the implicit "deny all" rule will drop all non-IP packets like ARP. Workaround : Use MAC ACL rule that permits all (permit any any) in conjunction with IPv6 ACL.

Firmware 5.0.0.15 pour GS748TP

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:53:45 +0200

Firmware 5.0.0.15 pour GS748TP

Bug Fixes :

Fixed the problem that device does not handle MSTP packets when its Spanning Tree configuration is set to RSTP.
Fixed the problem that GS748TP combo ports (port 45, 46, 47, and 48) may disconnect every few minutes and system log would show media type toggles between copper and fiber repeatedly.
Fixed the problem that the switch may reboot and the following log message would be generated: "FATAL ERROR: SW2M: ABORT DATA exception".

Limitations and Known Issues :

Although Management VLAN can now be changed from VLAN 1 to any other valid VLAN, egress packets still cannot be tagged with VLAN ID of 1.
When configuring IP ACL rule, system does not reject source address to be multicast address and accepts 0.0.0.0 masking.
When specify IPv6 ACL rule, the permit all (permit any any) rule would only forward the packet with IP header. As a result, the implicit "deny all" rule will drop all non-IP packets like ARP. Workaround : Use MAC ACL rule that permits all (permit any any) in conjunction with IPv6 ACL.

Firmware 5.0.0.15 pour GS724AT

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:53:45 +0200

Firmware 5.0.0.15 pour GS724AT

Bug Fixes :

Fixed the problem that device does not handle MSTP packets when its Spanning Tree configuration is set to RSTP.
Fixed the problem that GS748TP combo ports (port 45, 46, 47, and 48) may disconnect every few minutes and system log would show media type toggles between copper and fiber repeatedly.
Fixed the problem that the switch may reboot and the following log message would be generated: "FATAL ERROR: SW2M: ABORT DATA exception".

Limitations and Known Issues :

Although Management VLAN can now be changed from VLAN 1 to any other valid VLAN, egress packets still cannot be tagged with VLAN ID of 1.
When configuring IP ACL rule, system does not reject source address to be multicast address and accepts 0.0.0.0 masking.
When specify IPv6 ACL rule, the permit all (permit any any) rule would only forward the packet with IP header. As a result, the implicit "deny all" rule will drop all non-IP packets like ARP. Workaround : Use MAC ACL rule that permits all (permit any any) in conjunction with IPv6 ACL.

Firmware 5.0.0.15 pour GS748AT

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:53:45 +0200

Firmware 5.0.0.15 pour GS748AT

Bug Fixes :

Fixed the problem that device does not handle MSTP packets when its Spanning Tree configuration is set to RSTP.
Fixed the problem that GS748TP combo ports (port 45, 46, 47, and 48) may disconnect every few minutes and system log would show media type toggles between copper and fiber repeatedly.
Fixed the problem that the switch may reboot and the following log message would be generated: "FATAL ERROR: SW2M: ABORT DATA exception".

Limitations and Known Issues :

Although Management VLAN can now be changed from VLAN 1 to any other valid VLAN, egress packets still cannot be tagged with VLAN ID of 1.
When configuring IP ACL rule, system does not reject source address to be multicast address and accepts 0.0.0.0 masking.
When specify IPv6 ACL rule, the permit all (permit any any) rule would only forward the packet with IP header. As a result, the implicit "deny all" rule will drop all non-IP packets like ARP. Workaround : Use MAC ACL rule that permits all (permit any any) in conjunction with IPv6 ACL.

Firmware 2.0.1_02 pour FS726TP

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:50:44 +0200

Firmware 2.0.1_02 pour FS726TP

New Features :

Support the new Smart Control Center software

Known Issues :

Upgrade can only be done via the port that is a member of VLAN 1

Firmware 2.0.1_02 pour FS726T

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:48:30 +0200

Firmware 2.0.1_02 pour FS726T

New Features :

Support the new Smart Control Center software

Known Issues :

Upgrade can only be done via the port that is a member of VLAN 1

Firmware 1.0.0.2 pour WN2000RPT

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 28 Aug 2010 07:46:06 +0200

Firmware 1.0.0.2 pour WN2000RPT

New Features :

Initial Release firmware

Firmware 8.0.3.11 pour GSM7328S

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:48:51 +0200

Firmware 8.0.3.11 pour GSM7328S

Major Changes from v8.0.2.x and older releases :

Allow GSM7328S (v1), GSM7352S (v1), GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200 (v2), and GSM7352S-200 (v2), to be used in the same stack.
One firmware image to be used for all GSM7328S (v1), GSM7352S (v1), GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200 (v2), and GSM7352S-200 (v2).
Provide IPv6 Routing and IP Multicast upgrade capability to GSM7328S (v1), GSM7352S (v1), and GSM7328FS via software license.
Provide IPv4 and IPv6 dynamic routing, and IP multicast routing upgrade capability to GSM7228PS and GSM7252PS via software license.
Allow SFP+ front panel ports on GSM7228PS, GSM7252PS, GSM7328S-200, and GSM7352S-200 to be used for stacking application.

Open Issues :
GUI fails to show the MLD proxy entry
Description : The GUI page "IPv6 Multicast->MLD->Proxy Memebership" will not show table for the membership of MLD proxy.
Workaround : Use the CLI command "show ipv6 mld-proxy groups" to see the membership table.

On web GUI device view, the ports status and unit number fail to show on full 8 units stack.
Description : When the switches are stacked in the full 8 unit stack, the device view page in the web GUI might have difficulty shows all the ports' link status in real-time such that the link state might not be updated.
Workaround : No workaround.

The distribute list for OSPF route redistribution on GUI can not be removed.
Description : After configure OSFP route Distribution List through the GUI page of Routing->OSPF->Advanced->Route Redistribution, it is unable to remove the Distribution List by selecting the blank in the Distribute List filed.
Workaround : Disable the Redistribute Option and click the Apply button.

ISDP information with blank device ID doesn't show up on GUI
Description : Switch doesn't show ISDP neighbor information on GUI if the neighbor's device ID is blank.
Workaround: no workaround on GUI, please see the neighbor information through CLI.

Auto Install : download bootfile.cfg successfully, but an error showed up in GUI.
Description : after download bootfile.cfg successfully, an error message showed up on GUI with error "Auto Install Script file download through TFTP. Reason: Transfer direction is unknown."
Workaround : no workaround on GUI, please use CLI command to see the Auto Install status.

GUI doesn't show configured Policy attribute on policy configuration page.
Description: When you click the page of QoS->Diffserv->Advanced->Policy Configuration, GUI only shows the default configuration instead of the setting you have configured before.
Workaround : no workaround on GUI, please use CLI to see the configured setting for policy.

The switch console port will not to get into user login prompt after set the switch priority as 0 and reboot.
Description : If the switch priority for stacking mastership is changed to 0, and reboot the switch, the console will not go into user login prompt.
Workaround : no workaround, you have to go into utility menu to restore the configuration to the factory default.

Some IPv6 ACL CLI commands are missing.
Description : The CLI command 'ipv6 traffic-filter' under interface and
'show ipv6 access-lists' are missing.
Workaround : no workaround on CLI, please configure it through GUI.

The P-Bridge MIB objects, dot1dTpHCPortInDiscards, dot1dTpHCPortInFrames, and dot1dTpHCPortOutFrames not getting populated.
Description : These stats objects are not returning anything.
Workaround : no workaround

Firmware 8.0.3.11 pour GSM7352S

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:48:51 +0200

Firmware 8.0.3.11 pour GSM7352S

Major Changes from v8.0.2.x and older releases :

Allow GSM7328S (v1), GSM7352S (v1), GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200 (v2), and GSM7352S-200 (v2), to be used in the same stack.
One firmware image to be used for all GSM7328S (v1), GSM7352S (v1), GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200 (v2), and GSM7352S-200 (v2).
Provide IPv6 Routing and IP Multicast upgrade capability to GSM7328S (v1), GSM7352S (v1), and GSM7328FS via software license.
Provide IPv4 and IPv6 dynamic routing, and IP multicast routing upgrade capability to GSM7228PS and GSM7252PS via software license.
Allow SFP+ front panel ports on GSM7228PS, GSM7252PS, GSM7328S-200, and GSM7352S-200 to be used for stacking application.

Firmware 8.0.3.11 pour GSM7328FS

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:48:51 +0200

Firmware 8.0.3.11 pour GSM7328FS

Major Changes from v8.0.2.x and older releases :

Allow GSM7328S (v1), GSM7352S (v1), GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200 (v2), and GSM7352S-200 (v2), to be used in the same stack.
One firmware image to be used for all GSM7328S (v1), GSM7352S (v1), GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200 (v2), and GSM7352S-200 (v2).
Provide IPv6 Routing and IP Multicast upgrade capability to GSM7328S (v1), GSM7352S (v1), and GSM7328FS via software license.
Provide IPv4 and IPv6 dynamic routing, and IP multicast routing upgrade capability to GSM7228PS and GSM7252PS via software license.
Allow SFP+ front panel ports on GSM7228PS, GSM7252PS, GSM7328S-200, and GSM7352S-200 to be used for stacking application.

Firmware 8.0.1.9 pour GSM7328S

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:46:29 +0200

Firmware 8.0.1.9 pour GSM7328S

Enhancements from release 7.x :

IP Source Guard : Protect man-in-the-middle attack
ARP Guard : Protect against ARP spoofing attack
DHCP Snooping : Protect against disguised DHCP server
ACL over VLAN : Allow ACL control be applied to entire VLAN instead on a port only
Dynamic VLAN : Allow port's VLAN membership be determined by the RADIUS server
Guest VLAN :Allow creation of DMZ VLAN in company network
IPv6 Management : Allow the switch CPU management be part of IPv6 network
IPv6 Routing : Support routing of IPv6 packet. Only available via license.
4-to-6 Tunnel : Support tunneling of IPv6 to IPv4 traffic and vice versa
IP Multicast Routing : Support routing of IP multicast traffic for application like video streaming. Only available via license.
Dual Image : Provide backup firmware image in case the main image is corrupted during firmware upgrade
Captive Portal : Provide internet access authentication
Text-based Configuration : The switch configuration now is in text format when the configuration file is backup to the PC that it can be edited or reviewed easily
MLD Snooping : IPv6 multicast protocol snooping for forming IPv6 multicast group
RADIUS enhancements : Add backup RADIUS server, allow server redundancy. Support simultaneous transactions from the RADIUS client to multiple RADIUS servers
Denial Of Service Protection : Provide protection against common Internet Denial of Service attack
Voice VLAN : Support LLDP-MED enable IP Phone for creating special VLAN for priority treatment
IP subnet VLAN : Allow creation of VLAN based on the client device's IP address subnet
SCP, SFTP Firmware Upgrade : Support secure file transfer for firmware upgrade
Dynamic Stack : Allow stacking be constructed using optical cable
sFlow : Support traffic flow monitoring based on network flows
Auto VoIP : Support QOS treatment of IP phones.

Bug fixes from release 8.0.1.2 :

DHCP server IP address size is increased to 2000
AX744 (CX4) adapter card shown with "Fiber" type in "show port" output incorrectly
Sometime during firmware upgrade, there might be configuration corruption
The Spanning Tree Protocol Topology Change Notication (TCN) message in the logs is not saying the port in which TCN is received.
Stack master system prompt changed when master and backup models are different
IGMP Querier does not work with routing VLAN's
SNMP community string contains special characters not accepted in GUI. but works fine in CLI
SNMP Spanning Tree Protocol MIB object, dot1dTpFdbTable mibs, are missing
GUI page show system has wrong fan infor
Error message about temperature "...sensor 235 i2c operation failed" shows up in the logging buffer
TACACS+:telnet is unable to go into previlege mode when telnet use TACACS+ as enble method
The help description of DoS (Denied of Service) command is incorrect
When downgrading from 8.x to 7.x, the switch's MAC and serial number data would be lost
Boot menu option 13 doesn't recover password
AX744 ports need to change the MAC 10G port pre-emphasis and attenuation, otherwise there may be packet drops
Show interface switchport output missing "packet forwarded by CPU"
Switch will crash if "username" function is configured
Device sends IGMP Group Specific Query when IGMP Querier is not enabled.
Jump links are missing for "routing table" and "ip" in index page
Unable to goto the corresponding page when click site index->VLAN Routing Configuration
Online Support/User Guide/the image link on the top right of the GUI page is incorrect.
LLDP is sending out the wrong management IP address to the remote partner
The command "show ip pimdm interface stats all" doesn't show all of interface stats
Some command pop-up menu on GUI the device view has some issues
Switch doesn't accept the session-timeout in port based mode
Somehow 8.0 logged buffer reports event in the oldest event first
GUI : failed to show login help page.
Port Triggered Topology Change should be in u/s/p format
STP Topology change notification log message are mssing.
Maximum Number of Remote Connection Sessions should be 5 instead of 4
GUI MFDB : help information for the MFDB table is incorrect.
Failed to configure radius accounting server without the accounting server name on GUI

Firmware 8.0.1.9 pour GSM7352S

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:46:29 +0200

Firmware 8.0.1.9 pour GSM7352S

Enhancements from release 7.x :

IP Source Guard : Protect man-in-the-middle attack
ARP Guard : Protect against ARP spoofing attack
DHCP Snooping : Protect against disguised DHCP server
ACL over VLAN : Allow ACL control be applied to entire VLAN instead on a port only
Dynamic VLAN : Allow port's VLAN membership be determined by the RADIUS server
Guest VLAN :Allow creation of DMZ VLAN in company network
IPv6 Management : Allow the switch CPU management be part of IPv6 network
IPv6 Routing : Support routing of IPv6 packet. Only available via license.
4-to-6 Tunnel : Support tunneling of IPv6 to IPv4 traffic and vice versa
IP Multicast Routing : Support routing of IP multicast traffic for application like video streaming. Only available via license.
Dual Image : Provide backup firmware image in case the main image is corrupted during firmware upgrade
Captive Portal : Provide internet access authentication
Text-based Configuration : The switch configuration now is in text format when the configuration file is backup to the PC that it can be edited or reviewed easily
MLD Snooping : IPv6 multicast protocol snooping for forming IPv6 multicast group
RADIUS enhancements : Add backup RADIUS server, allow server redundancy. Support simultaneous transactions from the RADIUS client to multiple RADIUS servers
Denial Of Service Protection : Provide protection against common Internet Denial of Service attack
Voice VLAN : Support LLDP-MED enable IP Phone for creating special VLAN for priority treatment
IP subnet VLAN : Allow creation of VLAN based on the client device's IP address subnet
SCP, SFTP Firmware Upgrade : Support secure file transfer for firmware upgrade
Dynamic Stack : Allow stacking be constructed using optical cable
sFlow : Support traffic flow monitoring based on network flows
Auto VoIP : Support QOS treatment of IP phones.

Bug fixes from release 8.0.1.2 :

DHCP server IP address size is increased to 2000
AX744 (CX4) adapter card shown with "Fiber" type in "show port" output incorrectly
Sometime during firmware upgrade, there might be configuration corruption
The Spanning Tree Protocol Topology Change Notication (TCN) message in the logs is not saying the port in which TCN is received.
Stack master system prompt changed when master and backup models are different
IGMP Querier does not work with routing VLAN's
SNMP community string contains special characters not accepted in GUI. but works fine in CLI
SNMP Spanning Tree Protocol MIB object, dot1dTpFdbTable mibs, are missing
GUI page show system has wrong fan infor
Error message about temperature "...sensor 235 i2c operation failed" shows up in the logging buffer
TACACS+:telnet is unable to go into previlege mode when telnet use TACACS+ as enble method
The help description of DoS (Denied of Service) command is incorrect
When downgrading from 8.x to 7.x, the switch's MAC and serial number data would be lost
Boot menu option 13 doesn't recover password
AX744 ports need to change the MAC 10G port pre-emphasis and attenuation, otherwise there may be packet drops
Show interface switchport output missing "packet forwarded by CPU"
Switch will crash if "username" function is configured
Device sends IGMP Group Specific Query when IGMP Querier is not enabled.
Jump links are missing for "routing table" and "ip" in index page
Unable to goto the corresponding page when click site index->VLAN Routing Configuration
Online Support/User Guide/the image link on the top right of the GUI page is incorrect.
LLDP is sending out the wrong management IP address to the remote partner
The command "show ip pimdm interface stats all" doesn't show all of interface stats
Some command pop-up menu on GUI the device view has some issues
Switch doesn't accept the session-timeout in port based mode
Somehow 8.0 logged buffer reports event in the oldest event first
GUI : failed to show login help page.
Port Triggered Topology Change should be in u/s/p format
STP Topology change notification log message are mssing.
Maximum Number of Remote Connection Sessions should be 5 instead of 4
GUI MFDB : help information for the MFDB table is incorrect.
Failed to configure radius accounting server without the accounting server name on GUI

Firmware 8.0.1.9 pour GSM7328FS

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:46:29 +0200

Firmware 8.0.1.9 pour GSM7328FS

Enhancements from release 7.x :

IP Source Guard : Protect man-in-the-middle attack
ARP Guard : Protect against ARP spoofing attack
DHCP Snooping : Protect against disguised DHCP server
ACL over VLAN : Allow ACL control be applied to entire VLAN instead on a port only
Dynamic VLAN : Allow port's VLAN membership be determined by the RADIUS server
Guest VLAN :Allow creation of DMZ VLAN in company network
IPv6 Management : Allow the switch CPU management be part of IPv6 network
IPv6 Routing : Support routing of IPv6 packet. Only available via license.
4-to-6 Tunnel : Support tunneling of IPv6 to IPv4 traffic and vice versa
IP Multicast Routing : Support routing of IP multicast traffic for application like video streaming. Only available via license.
Dual Image : Provide backup firmware image in case the main image is corrupted during firmware upgrade
Captive Portal : Provide internet access authentication
Text-based Configuration : The switch configuration now is in text format when the configuration file is backup to the PC that it can be edited or reviewed easily
MLD Snooping : IPv6 multicast protocol snooping for forming IPv6 multicast group
RADIUS enhancements : Add backup RADIUS server, allow server redundancy. Support simultaneous transactions from the RADIUS client to multiple RADIUS servers
Denial Of Service Protection : Provide protection against common Internet Denial of Service attack
Voice VLAN : Support LLDP-MED enable IP Phone for creating special VLAN for priority treatment
IP subnet VLAN : Allow creation of VLAN based on the client device's IP address subnet
SCP, SFTP Firmware Upgrade : Support secure file transfer for firmware upgrade
Dynamic Stack : Allow stacking be constructed using optical cable
sFlow : Support traffic flow monitoring based on network flows
Auto VoIP : Support QOS treatment of IP phones.

Bug fixes from release 8.0.1.2 :

DHCP server IP address size is increased to 2000
AX744 (CX4) adapter card shown with "Fiber" type in "show port" output incorrectly
Sometime during firmware upgrade, there might be configuration corruption
The Spanning Tree Protocol Topology Change Notication (TCN) message in the logs is not saying the port in which TCN is received.
Stack master system prompt changed when master and backup models are different
IGMP Querier does not work with routing VLAN's
SNMP community string contains special characters not accepted in GUI. but works fine in CLI
SNMP Spanning Tree Protocol MIB object, dot1dTpFdbTable mibs, are missing
GUI page show system has wrong fan infor
Error message about temperature "...sensor 235 i2c operation failed" shows up in the logging buffer
TACACS+:telnet is unable to go into previlege mode when telnet use TACACS+ as enble method
The help description of DoS (Denied of Service) command is incorrect
When downgrading from 8.x to 7.x, the switch's MAC and serial number data would be lost
Boot menu option 13 doesn't recover password
AX744 ports need to change the MAC 10G port pre-emphasis and attenuation, otherwise there may be packet drops
Show interface switchport output missing "packet forwarded by CPU"
Switch will crash if "username" function is configured
Device sends IGMP Group Specific Query when IGMP Querier is not enabled.
Jump links are missing for "routing table" and "ip" in index page
Unable to goto the corresponding page when click site index->VLAN Routing Configuration
Online Support/User Guide/the image link on the top right of the GUI page is incorrect.
LLDP is sending out the wrong management IP address to the remote partner
The command "show ip pimdm interface stats all" doesn't show all of interface stats
Some command pop-up menu on GUI the device view has some issues
Switch doesn't accept the session-timeout in port based mode
Somehow 8.0 logged buffer reports event in the oldest event first
GUI : failed to show login help page.
Port Triggered Topology Change should be in u/s/p format
STP Topology change notification log message are mssing.
Maximum Number of Remote Connection Sessions should be 5 instead of 4
GUI MFDB : help information for the MFDB table is incorrect.
Failed to configure radius accounting server without the accounting server name on GUI

Firmware 1.0.2.50 pour WNR3500L

noreply@netgear-forum.com(NETGEAR Firmware) — Wed, 25 Aug 2010 06:38:35 +0200

Firmware 1.0.2.50 pour WNR3500L

New Features, Enhancemens and Bug Fixes :

This is a Wi-Fi certified firmware.
The 11n rates are disabled when the security type is WPS-TKIP.
No reboot is needed for a configuration change from the GUI.
Traffic Meter: Maximum volume of monthly limit is increased from 99GB (5 digits) to 999GB (6 digits).
The login pop-up window is removed.
The USB storage access performance is improved.
Improved compatibility with external USB storage devices.
Increase the max number of NAT session to 4096 sessions at a time.
Fixed : Firmware Upgrade - When the Apple Safari version 2.0.4 is used to access the router’s management GUI and upgrade the firmware, the progress bar cannot be displayed. The firmware upgrade is still working, and the “Update Settings” progress bar shows up after the firmware upgrade is done.
Fixed : Traffic Meter - If the traffic meter function is enabled and the user’s setting is to block the traffic after the limit has been reached, then when the traffic volume limit is reached, the Internet traffic is blocked as expected. But after a router reboot, the Internet traffic will not be blocked.
Fixed : Traffic Meter - The option “Turn the Internet LED to flashing green/amber" doesn't work if the option "Disconnect and disable the Internet connection" is not checked.
Fixed : Log - At the Logs page, the Clear log button and Send log buttons do not work.

Firmware 3.0.0.29 pour FS752TPS

noreply@netgear-forum.com(NETGEAR Firmware) — Sat, 21 Aug 2010 12:28:24 +0200

Firmware 3.0.0.29 pour FS752TPS

Important Note :

Please make sure the bootcode version of your FS700TS smart switch is V1.0.0.8 before upgrading the firmware to this version.
Please read the upgrade and downgrade instruction carefully before upgrading to the firmware version or downgrading to older firmware. Improper upgrade procedure may cause the device to become inoperable and must be replaced

Bug Fixes :

Fixed the bug that System Up Time (sysUpTime) obtained via SNMP is incorrect.

Limitations and Known Issues :

Only members of default VLAN (VLAN ID of 1) can manage the switch.
Changing the default PVID would automatically remove the port from VLAN 1.
Refreshing the page (Ctrl+F5) will always bring you back to the first page, which is the System Information page. Workaround : Please manually navigate to the desired page again.
The VLAN name does not get displayed correctly in the Multicast Group configuration table under Switching > Multicast > Advanced page. Workaround : This does not prevent you from creating the multicast group, as long as the correct VLAN ID is selected.
The display format of Local Engine ID is inconsistent with the input format under System > SNMP > SNMPv3 > Engine ID page. The display format is with colon “:” (eg. 00:e3:ab:cd:12:56). But, the input format must be without the colon (eg. 00e3abcd1256). Workaround : Please enter the Engine ID without the colon. It will be fixed in the next release.
Authentication method is not shown after configuring it under System > SNMP > SNMPv3 > User Configuration page. Workaround : None. It will be fixed in the next release.